Audio base, Insulator, Audio Accessories Page 4

VB-25 Product made from ebony V character slot receptacle base
2 pcs. set \12,000 (according to tax) withstand load: 60kg (two pieces)
It is the base made from a 35mm(width) x33mm(height) x250mm (length) ebony manufactured by a completely new view. It is a form where the triangular prism type spacer rode on the square lumber to which the V character type slot was attached. An up-and-down point of contact becomes a line, and controls vibration effectively. An up-and-down side is even, and since stability is good, even if it uses it for a speaker etc., it does not become unstable but is safe. One set is used for amplifier and two sets are used for a speaker. Since it is somewhat larger than VB-18, the vibration control effect also becomes large, and it can respond also to inside and large-sized apparatus.

MGB-1 Magnet floating base
Four pieces are constructed, \38,000, three pieces are constructed, \29,000, one piece is \10,000 (simple packaging) (according to tax). Withstand load: 2kg - 10kg per piece
MGB-1 is an arrangement base which intercepts vibration using magnetism. The repulsion of the magnet was used and the epoch-making composition of carrying out floating of the use apparatus is adopted. The highest Neodium magnet of holding power is adopted as a magnet, and it is designing use it also for quite heavy apparatus. At the time of three-piece use, it can respond to apparatus as wide range as 6 to 30kg. It is effective for an analog player or CD player. Outside dimension: 59mm in diameter, and height:58.8mm -47mm (it changes with loads)

MGB-2 Magnet floating base
constructing four pieces and constructing \28,000, three pieces \21,000, one piece \7,000 (simple packaging) withstand-load: 0.9kg - 3kg per piece
MGB-2 is an arrangement base which intercepts vibration using magnetism. The repulsion of the magnet was used and the epoch-making composition of carrying out floating of the use apparatus is adopted. The highest Neodium magnet of holding power is adopted as a magnet, and it is designed respond to apparatus lighter than MGB-1. At the time of three-piece use, it can respond to 2.7 to 9kg apparatus. It is effective for audio amplifier or CD player. Outside dimension: 49mm in diameter, and height:45mm -37mm (it changes with loads)
A rubber spacer with double-stick tape the diameter of 20mm
GS-1 0.5mm thickness rubber spacer
40-piece set \600 (according to tax),
GS-2 2mm thickness sponge rubber spacer
30-piece set \600 (according to tax),
GS-3 3mm thickness rubber spacer
20-piece set \600 (according to tax),
When installing a speaker system, a rack, an insulator, etc., it is a spacer made of rubber which cancels shakiness, a slide low price, etc. Since the back has all three kinds of double-stick tape, it can be used being able to stick on use apparatus. GS-1 and GS-3 are the product made of CR rubber and GS-2 the products made from SBR sponge.
A spacer with double-stick tape the diameter of 20mm
GS-4 Spacer made from 1mm thickness felt
20-piece set \600 (according to tax),
GS-6 Spacer made of 0.8mm thickness chamois leather
20-piece set \900 (according to tax),
It is a spacer which shakes when installing a speaker system, a rack, an insulator, etc., and is used for prevention of a crack. Since the back has all two kinds of double-stick tape, it can be used being able to stick on use apparatus. The product made from white felt with GS-4 and GS-6 are the products made of chamois leather (buckskin). These are both soft and useful for crack prevention of apparatus at the time of installation. In addition, variation may come out of chamois leather to thickness for a natural material.
DK-25 Stand for large-sized speakers
\36,000 (a tax exception, one set) withstand load: 100kg
It is a speaker stand for large-sized speakers. It is the highly efficient stand which stood the support by the pure material of the 10cm angle of Asada Cherry wood to four corners, and was supported at the joint by the cherry tree plywood of a central portion. Since a support is started downward, as for the weight of a speaker, the speaker of about 100kg heavy weight class is also stabilized, and it can be installed. A normalized form is 440x650x250 (H) in the object for JBL4333. It can respond to the speaker of various sizes by changing the size of a support and joint. Since special order size is also possible, ask a price etc. to our company.